It is essential that you regularly check and treat the water in your Wave Spa to get full enjoyment and to extend your Wave Spa’s life.

WATER TREATMENT CHEMICAL INSTRUCTIONS

We recommend the Wave Spa range of chemicals - Click Here for Chlorine Tablets / Chlorine Granules 
Before you add any water treatment chemicals to your spa please read the instructions on the label.
Do not add chemicals to your spa when it is occupied by anyone.
Only add chemicals to your spa when water is being circulated.
Only add chemicals that are totally dissolved to your spa.
Make sure you do not mix chemicals together as some chemicals can explode or create poisonous gases if mixed together. Water treatment chemicals are highly concentrated.
Always clean or replace the filter cartridge when you drain or refill your spa. Remove any stagnant water before you start to refill.
Water treatment chemicals should be handled carefully in a well ventilated area and your hands should be thoroughly cleaned after using chemicals.
Water treatment chemicals should always be stored in a cool, dry, secure area well out of the reach of children.

DISINFECTING THE WATER INSIDE YOUR HOT TUB

We recommend Wave Spa Chlorine Granules - Click Here for Chlorine Granules
The use of Wave Spa Chlorine Granules is the best way to sanitise your spa water and the spa needs to be chlorinated all the time.
You must always test daily the Chlorine level in your spa water, and always before use.

The most ideal Chlorine level is between 3-5 parts per million.
If your Chlorine level is lower than 3 parts per million then please use the following instructions.

a) Dissolve the correct amount of granules in warm water inside a clean plastic bucket, stirring until completely dissolved.
b) Turn your spa circulation pump on and pour the content of the bucket directly onto the surface of the spa water.
c) After 15 to 20 minutes with the spa circulation pump still running, test again the spa water. If the Chlorine level is still too low, repeat the operation until the level is 3-5 parts per million.
d) Do not use your spa for 15 to 20 minutes
e) Generally to chlorinate you will need to add approximately 3g of granules for each part per million.

So for a 4 person Wave Spa you would need to add as follows:
Initial set up 6 gms (3/4 teaspoon) to take to 4 parts per million and every day add a further 1.5 gms
And for a 6 person Wave Spa you would need to add as follows:
Initial set up 8 gms ( 1 teaspoon) to take to 4 parts per million and every day add a further 2 gms (1/4 teaspoon).

MAINTAINING PH LEVELS IN YOUR HOT TUB

Maintaining the correct pH levels in your Wave Spa is essential. The most ideal pH level is between 7.2 to 7.6 and the level should be tested two times each week, and always before use.
A heaped teaspoon holds approximately 8g of granules

INCREASING pH LEVELS IN YOUR HOT TUB

We recommend Wave Spa pH chemical products - Click Here for pH Increaser

If the pH level of the spa water is less than 7.2 add the Wave Spa pH Increaser using the following instructions

a) Dissolve the correct amount of Wave Spa pH Increaser in warm water inside a clean plastic bucket, until completely dissolved.
b) Turn your spa circulation pump on and pour the content of the bucket directly onto the surface of the spa water.
c) After 15 to 20 minutes with the spa circulation pump still running, test again the spa water. If the pH level is still too low, repeat the operation until the level of between 7.2 and 7.6 is reached.
d) Do not use your spa for 15 to 20 minutes

DECREASING pH LEVELS IN YOUR HOT TUB

We recommend Wave Spa pH Reducer - Click Here for pH Reducer
If the pH level of the spa water is more than 7.2 add the Wave Spa pH Reducer using the following instructions
a) Dissolve the correct amount of Wave Spa pH Increaser in warm water inside a clean plastic bucket, until completely dissolved.
b) Turn your spa circulation pump on and pour the content of the bucket directly onto the surface of the spa water.
c) After 15 to 20 minutes with the spa circulation pump still running, test again the spa water. If the pH level is still too low, repeat the operation until the level of between 7.2 and 7.6 is reached.
d) Do not use your spa for 15 to 20 minutes

REMOVING AND PREVENTING FOAM

We recommend Wave Spa No Foam - Click Here for No Foam

If you allow foaming to build up in your Spa water (caused by soaps, oils and cosmetics and other contaminants) you should remove the foam using Wave Spa No Foam. Never allow your spa water to foam excessively, and remove it using the following instructions:

a) Shake plastic canister before using
b) Turn your spa circulation pump on and pour the correct dose directly onto the surface of the spa water.
c) After 15 minutes if the foam has not completely been removed repeat the same dose
d) Do not use your spa for 15 to 20 minutes
e) To reduce foam you should shower before entering your spa

ADDITIONAL INFORMATION FOR THE WAVE SPA

 Maintaining and treating your water in your Wave Spa is essential to maximise your enjoyment and safety, both from a hygiene perspective as well as extending the life of your Hot Tub. 

To keep your Wave Spa in excellent condition you should always use the correct chemicals and change your filters often.
Also change your spa water often, particularly when used often
You must use the correct chemicals and regularly change your filters to prevent water borne diseases such as Legionella.
You should always use correct spa products whilst cleaning any areas around your hot tub. Do not use household cleaners as they can contain phosphates which allows algae to grow and do not use household detergents as they cause foaming.
Wave Spa produces an exclusive range of Wave Spa chemicals and these can also be used on any other makes of hot tub's water treatment.

If you need further information contact support@wavespas.com